148 lines
4.2 KiB
Text
148 lines
4.2 KiB
Text
Mediatek HDMI Encoder
|
|
=====================
|
|
|
|
The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
|
|
its parallel input.
|
|
|
|
Required properties:
|
|
- compatible: Should be "mediatek,<chip>-hdmi".
|
|
- reg: Physical base address and length of the controller's registers
|
|
- interrupts: The interrupt signal from the function block.
|
|
- clocks: device clocks
|
|
See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
|
|
- clock-names: must contain "pixel", "pll", "bclk", and "spdif".
|
|
- phys: phandle link to the HDMI PHY node.
|
|
See Documentation/devicetree/bindings/phy/phy-bindings.txt for details.
|
|
- phy-names: must contain "hdmi"
|
|
- mediatek,syscon-hdmi: phandle link and register offset to the system
|
|
configuration registers. For mt8173 this must be offset 0x900 into the
|
|
MMSYS_CONFIG region: <&mmsys 0x900>.
|
|
- ports: A node containing input and output port nodes with endpoint
|
|
definitions as documented in Documentation/devicetree/bindings/graph.txt.
|
|
- port@0: The input port in the ports node should be connected to a DPI output
|
|
port.
|
|
- port@1: The output port in the ports node should be connected to the input
|
|
port of a connector node that contains a ddc-i2c-bus property, or to the
|
|
input port of an attached bridge chip, such as a SlimPort transmitter.
|
|
|
|
HDMI CEC
|
|
========
|
|
|
|
The HDMI CEC controller handles hotplug detection and CEC communication.
|
|
|
|
Required properties:
|
|
- compatible: Should be "mediatek,<chip>-cec"
|
|
- reg: Physical base address and length of the controller's registers
|
|
- interrupts: The interrupt signal from the function block.
|
|
- clocks: device clock
|
|
|
|
HDMI DDC
|
|
========
|
|
|
|
The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
|
|
The Mediatek's I2C controller is used to interface with I2C devices.
|
|
|
|
Required properties:
|
|
- compatible: Should be "mediatek,<chip>-hdmi-ddc"
|
|
- reg: Physical base address and length of the controller's registers
|
|
- clocks: device clock
|
|
- clock-names: Should be "ddc-i2c".
|
|
|
|
HDMI PHY
|
|
========
|
|
|
|
The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel
|
|
output and drives the HDMI pads.
|
|
|
|
Required properties:
|
|
- compatible: "mediatek,<chip>-hdmi-phy"
|
|
- reg: Physical base address and length of the module's registers
|
|
- clocks: PLL reference clock
|
|
- clock-names: must contain "pll_ref"
|
|
- clock-output-names: must be "hdmitx_dig_cts" on mt8173
|
|
- #phy-cells: must be <0>
|
|
- #clock-cells: must be <0>
|
|
|
|
Optional properties:
|
|
- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa
|
|
- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c
|
|
|
|
Example:
|
|
|
|
cec: cec@10013000 {
|
|
compatible = "mediatek,mt8173-cec";
|
|
reg = <0 0x10013000 0 0xbc>;
|
|
interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
|
|
clocks = <&infracfg CLK_INFRA_CEC>;
|
|
};
|
|
|
|
hdmi_phy: hdmi-phy@10209100 {
|
|
compatible = "mediatek,mt8173-hdmi-phy";
|
|
reg = <0 0x10209100 0 0x24>;
|
|
clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
|
|
clock-names = "pll_ref";
|
|
clock-output-names = "hdmitx_dig_cts";
|
|
mediatek,ibias = <0xa>;
|
|
mediatek,ibias_up = <0x1c>;
|
|
#clock-cells = <0>;
|
|
#phy-cells = <0>;
|
|
};
|
|
|
|
hdmi_ddc0: i2c@11012000 {
|
|
compatible = "mediatek,mt8173-hdmi-ddc";
|
|
reg = <0 0x11012000 0 0x1c>;
|
|
interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
|
|
clocks = <&pericfg CLK_PERI_I2C5>;
|
|
clock-names = "ddc-i2c";
|
|
};
|
|
|
|
hdmi0: hdmi@14025000 {
|
|
compatible = "mediatek,mt8173-hdmi";
|
|
reg = <0 0x14025000 0 0x400>;
|
|
interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
|
|
clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
|
|
<&mmsys CLK_MM_HDMI_PLLCK>,
|
|
<&mmsys CLK_MM_HDMI_AUDIO>,
|
|
<&mmsys CLK_MM_HDMI_SPDIF>;
|
|
clock-names = "pixel", "pll", "bclk", "spdif";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&hdmi_pin>;
|
|
phys = <&hdmi_phy>;
|
|
phy-names = "hdmi";
|
|
mediatek,syscon-hdmi = <&mmsys 0x900>;
|
|
assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>;
|
|
assigned-clock-parents = <&hdmi_phy>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
|
|
hdmi0_in: endpoint {
|
|
remote-endpoint = <&dpi0_out>;
|
|
};
|
|
};
|
|
|
|
port@1 {
|
|
reg = <1>;
|
|
|
|
hdmi0_out: endpoint {
|
|
remote-endpoint = <&hdmi_con_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
connector {
|
|
compatible = "hdmi-connector";
|
|
type = "a";
|
|
ddc-i2c-bus = <&hdmiddc0>;
|
|
|
|
port {
|
|
hdmi_con_in: endpoint {
|
|
remote-endpoint = <&hdmi0_out>;
|
|
};
|
|
};
|
|
};
|