88 lines
2.9 KiB
Text
88 lines
2.9 KiB
Text
Binding for Samsung S2M and S5M family multi-function device
|
|
============================================================
|
|
|
|
This is a part of device tree bindings for S2M and S5M family multi-function
|
|
devices.
|
|
|
|
The Samsung S2MPA01, S2MPS11/13/14/15, S2MPU02 and S5M8767 is a family
|
|
of multi-function devices which include voltage and current regulators, RTC,
|
|
charger controller, clock outputs and other sub-blocks. It is interfaced
|
|
to the host controller using an I2C interface. Each sub-block is usually
|
|
addressed by the host system using different I2C slave addresses.
|
|
|
|
|
|
This document describes bindings for main device node. Optional sub-blocks
|
|
must be a sub-nodes to it. Bindings for them can be found in:
|
|
- bindings/regulator/samsung,s2mpa01.txt
|
|
- bindings/regulator/samsung,s2mps11.txt
|
|
- bindings/regulator/samsung,s5m8767.txt
|
|
- bindings/clock/samsung,s2mps11.txt
|
|
|
|
|
|
Required properties:
|
|
- compatible: Should be one of the following
|
|
- "samsung,s2mpa01-pmic",
|
|
- "samsung,s2mps11-pmic",
|
|
- "samsung,s2mps13-pmic",
|
|
- "samsung,s2mps14-pmic",
|
|
- "samsung,s2mps15-pmic",
|
|
- "samsung,s2mpu02-pmic",
|
|
- "samsung,s5m8767-pmic".
|
|
- reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
|
|
|
|
Optional properties:
|
|
- interrupt-parent: Specifies the phandle of the interrupt controller to which
|
|
the interrupts from s2mps11 are delivered to.
|
|
- interrupts: Interrupt specifiers for interrupt sources.
|
|
- samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled
|
|
down. When the system is suspended it will always go down thus triggerring
|
|
unwanted buck warm reset (setting buck voltages to default values).
|
|
- samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is
|
|
connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1
|
|
register to turn off the power. Usually the ACOKB is pulled up to VBATT so
|
|
when PWRHOLD pin goes low, the rising ACOKB will trigger power off.
|
|
|
|
Example:
|
|
|
|
s2mps11_pmic@66 {
|
|
compatible = "samsung,s2mps11-pmic";
|
|
reg = <0x66>;
|
|
|
|
s2m_osc: clocks {
|
|
compatible = "samsung,s2mps11-clk";
|
|
#clock-cells = <1>;
|
|
clock-output-names = "xx", "yy", "zz";
|
|
};
|
|
|
|
regulators {
|
|
ldo1_reg: LDO1 {
|
|
regulator-name = "VDD_ABB_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
};
|
|
|
|
ldo2_reg: LDO2 {
|
|
regulator-name = "VDD_ALIVE_1.1V";
|
|
regulator-min-microvolt = <1100000>;
|
|
regulator-max-microvolt = <1100000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck1_reg: BUCK1 {
|
|
regulator-name = "vdd_mif";
|
|
regulator-min-microvolt = <950000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
buck2_reg: BUCK2 {
|
|
regulator-name = "vdd_arm";
|
|
regulator-min-microvolt = <950000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
regulator-ramp-delay = <50000>;
|
|
};
|
|
};
|
|
};
|